Add BLTouch bed leveling

Marlin/Configuration.h

@@ -1259,7 +1259,7 @@
 /**
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
-//#define BLTOUCH
+#define BLTOUCH
 
 /**
  * MagLev V4 probe by MDD
@@ -1390,7 +1390,7 @@
  *     |    [-]    |
  *     O-- FRONT --+
  */
-#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
+#define NOZZLE_TO_PROBE_OFFSET { -56.5, -7, 0 }
 
 // Most probes should stay away from the edges of the bed, but
 // with NOZZLE_AS_PROBE this can be negative for a wider probing area.
@@ -1749,7 +1749,7 @@
  */
 //#define AUTO_BED_LEVELING_3POINT
 //#define AUTO_BED_LEVELING_LINEAR
-//#define AUTO_BED_LEVELING_BILINEAR
+#define AUTO_BED_LEVELING_BILINEAR
 //#define AUTO_BED_LEVELING_UBL
 //#define MESH_BED_LEVELING
 
@@ -1758,7 +1758,7 @@
  * these options to restore the prior leveling state or to always enable
  * leveling immediately after G28.
  */
-//#define RESTORE_LEVELING_AFTER_G28
+#define RESTORE_LEVELING_AFTER_G28
 //#define ENABLE_LEVELING_AFTER_G28
 
 /**
@@ -1800,7 +1800,7 @@
   /**
    * Enable the G26 Mesh Validation Pattern tool.
    */
-  //#define G26_MESH_VALIDATION
+  #define G26_MESH_VALIDATION
   #if ENABLED(G26_MESH_VALIDATION)
     #define MESH_TEST_NOZZLE_SIZE    0.4  // (mm) Diameter of primary nozzle.
     #define MESH_TEST_LAYER_HEIGHT   0.2  // (mm) Default layer height for G26.
@@ -1826,7 +1826,7 @@
 
     // Beyond the probed grid, continue the implied tilt?
     // Default is to maintain the height of the nearest edge.
-    //#define EXTRAPOLATE_BEYOND_GRID
+    #define EXTRAPOLATE_BEYOND_GRID
 
     //
     // Experimental Subdivision of the grid by Catmull-Rom method.
@@ -1880,7 +1880,7 @@
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */
-//#define LCD_BED_LEVELING
+#define LCD_BED_LEVELING
 
 #if ENABLED(LCD_BED_LEVELING)
   #define MESH_EDIT_Z_STEP  0.025 // (mm) Step size while manually probing Z axis.

Marlin/Configuration_adv.h

@@ -1954,7 +1954,7 @@
  *
  * Warning: Does not respect endstops!
  */
-//#define BABYSTEPPING
+#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
   //#define INTEGRATED_BABYSTEPPING         // EXPERIMENTAL integration of babystepping into the Stepper ISR
   //#define BABYSTEP_WITHOUT_HOMING
@@ -1977,7 +1977,7 @@
 
   //#define BABYSTEP_DISPLAY_TOTAL          // Display total babysteps since last G28
 
-  //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
+  #define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets
     //#define BABYSTEP_ZPROBE_GFX_OVERLAY   // Enable graphical overlay on Z-offset editor