Commit existing changes

- not sure if this is what is currently flashed

Marlin/Configuration.h

@@ -121,14 +121,14 @@
  *
  * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
  */
-#define BAUDRATE 250000
+#define BAUDRATE 115200
 
 // Enable the Bluetooth serial interface on AT90USB devices
 //#define BLUETOOTH
 
 // Choose the name from boards.h that matches your setup
 #ifndef MOTHERBOARD
-  #define MOTHERBOARD BOARD_RAMPS_14_EFB
+  #define MOTHERBOARD BOARD_MKS_GEN_13
 #endif
 
 // Name displayed in the LCD "Ready" message and Info menu
@@ -424,7 +424,7 @@
 #define TEMP_SENSOR_5 0
 #define TEMP_SENSOR_6 0
 #define TEMP_SENSOR_7 0
-#define TEMP_SENSOR_BED 0
+#define TEMP_SENSOR_BED 1
 #define TEMP_SENSOR_PROBE 0
 #define TEMP_SENSOR_CHAMBER 0
 
@@ -490,9 +490,9 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  #define DEFAULT_Kp 22.2
-  #define DEFAULT_Ki 1.08
-  #define DEFAULT_Kd 114
+  // #define DEFAULT_Kp 22.2
+  // #define DEFAULT_Ki 1.08
+  // #define DEFAULT_Kd 114
 
   // MakerGear
   //#define DEFAULT_Kp 7.0
@@ -504,6 +504,11 @@
   //#define DEFAULT_Ki 2.25
   //#define DEFAULT_Kd 440
 
+  // RigidBot
+  #define DEFAULT_Kp 9.06
+  #define DEFAULT_Ki 0.52
+  #define DEFAULT_Kd 60.28
+
 #endif // PIDTEMP
 
 //===========================================================================
@@ -523,7 +528,7 @@
  * heater. If your configuration is significantly different than this and you don't understand
  * the issues involved, don't use bed PID until someone else verifies that your hardware works.
  */
-//#define PIDTEMPBED
+#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
@@ -541,9 +546,9 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define DEFAULT_bedKp 10.00
-  #define DEFAULT_bedKi .023
-  #define DEFAULT_bedKd 305.4
+  // #define DEFAULT_bedKp 10.00
+  // #define DEFAULT_bedKi .023
+  // #define DEFAULT_bedKd 305.4
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
@@ -551,6 +556,11 @@
   //#define DEFAULT_bedKi 1.41
   //#define DEFAULT_bedKd 1675.16
 
+  // RigidBot
+  #define  DEFAULT_bedKp 355
+  #define  DEFAULT_bedKi 66.5
+  #define  DEFAULT_bedKd 480
+
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED
 
@@ -660,12 +670,12 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
 #define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
 
 /**
@@ -684,22 +694,22 @@
  *          TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE
  * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'L6474', 'POWERSTEP01', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
  */
-//#define X_DRIVER_TYPE  A4988
-//#define Y_DRIVER_TYPE  A4988
-//#define Z_DRIVER_TYPE  A4988
-//#define X2_DRIVER_TYPE A4988
-//#define Y2_DRIVER_TYPE A4988
-//#define Z2_DRIVER_TYPE A4988
-//#define Z3_DRIVER_TYPE A4988
-//#define Z4_DRIVER_TYPE A4988
-//#define E0_DRIVER_TYPE A4988
-//#define E1_DRIVER_TYPE A4988
-//#define E2_DRIVER_TYPE A4988
-//#define E3_DRIVER_TYPE A4988
-//#define E4_DRIVER_TYPE A4988
-//#define E5_DRIVER_TYPE A4988
-//#define E6_DRIVER_TYPE A4988
-//#define E7_DRIVER_TYPE A4988
+#define X_DRIVER_TYPE  TMC2209
+#define Y_DRIVER_TYPE  TMC2209
+#define Z_DRIVER_TYPE  DRV8825
+#define X2_DRIVER_TYPE DRV8825
+#define Y2_DRIVER_TYPE DRV8825
+#define Z2_DRIVER_TYPE DRV8825
+#define Z3_DRIVER_TYPE DRV8825
+#define Z4_DRIVER_TYPE DRV8825
+#define E0_DRIVER_TYPE TMC2209
+#define E1_DRIVER_TYPE DRV8825
+#define E2_DRIVER_TYPE DRV8825
+#define E3_DRIVER_TYPE DRV8825
+#define E4_DRIVER_TYPE DRV8825
+#define E5_DRIVER_TYPE DRV8825
+#define E6_DRIVER_TYPE DRV8825
+#define E7_DRIVER_TYPE DRV8825
 
 // Enable this feature if all enabled endstop pins are interrupt-capable.
 // This will remove the need to poll the interrupt pins, saving many CPU cycles.
@@ -747,14 +757,14 @@
  * Override with M92
  *                                      X, Y, Z, E0 [, E1[, E2...]]
  */
-#define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, 4000, 500 }
+#define DEFAULT_AXIS_STEPS_PER_UNIT   { 80.8, 80, 3200, 114.3 }  // 1/16 1/16 1/32 1/16 microsteps
 
 /**
  * Default Max Feed Rate (mm/s)
  * Override with M203
  *                                      X, Y, Z, E0 [, E1[, E2...]]
  */
-#define DEFAULT_MAX_FEEDRATE          { 300, 300, 5, 25 }
+#define DEFAULT_MAX_FEEDRATE          { 500, 500, 4, 25 }
 
 //#define LIMITED_MAX_FR_EDITING        // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
 #if ENABLED(LIMITED_MAX_FR_EDITING)
@@ -767,7 +777,7 @@
  * Override with M201
  *                                      X, Y, Z, E0 [, E1[, E2...]]
  */
-#define DEFAULT_MAX_ACCELERATION      { 3000, 3000, 100, 10000 }
+#define DEFAULT_MAX_ACCELERATION      { 600, 600, 100, 10000 }
 
 //#define LIMITED_MAX_ACCEL_EDITING     // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
 #if ENABLED(LIMITED_MAX_ACCEL_EDITING)
@@ -782,8 +792,8 @@
  *   M204 R    Retract Acceleration
  *   M204 T    Travel Acceleration
  */
-#define DEFAULT_ACCELERATION          3000    // X, Y, Z and E acceleration for printing moves
-#define DEFAULT_RETRACT_ACCELERATION  3000    // E acceleration for retracts
+#define DEFAULT_ACCELERATION          600    // X, Y, Z and E acceleration for printing moves
+#define DEFAULT_RETRACT_ACCELERATION  1000    // E acceleration for retracts
 #define DEFAULT_TRAVEL_ACCELERATION   3000    // X, Y, Z acceleration for travel (non printing) moves
 
 /**
@@ -794,11 +804,11 @@
  * When changing speed and direction, if the difference is less than the
  * value set here, it may happen instantaneously.
  */
-//#define CLASSIC_JERK
+#define CLASSIC_JERK
 #if ENABLED(CLASSIC_JERK)
-  #define DEFAULT_XJERK 10.0
-  #define DEFAULT_YJERK 10.0
-  #define DEFAULT_ZJERK  0.3
+  #define DEFAULT_YJERK 10
+  #define DEFAULT_XJERK 10
+  #define DEFAULT_ZJERK 0.4
 
   //#define TRAVEL_EXTRA_XYJERK 0.0     // Additional jerk allowance for all travel moves
 
@@ -1083,14 +1093,14 @@
 // @section machine
 
 // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
-#define INVERT_X_DIR false
-#define INVERT_Y_DIR true
-#define INVERT_Z_DIR false
+#define INVERT_X_DIR true
+#define INVERT_Y_DIR false
+#define INVERT_Z_DIR true
 
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.
-#define INVERT_E0_DIR false
+#define INVERT_E0_DIR true
 #define INVERT_E1_DIR false
 #define INVERT_E2_DIR false
 #define INVERT_E3_DIR false
@@ -1119,16 +1129,18 @@
 // @section machine
 
 // The size of the print bed
-#define X_BED_SIZE 200
-#define Y_BED_SIZE 200
+#define X_BED_SIZE 254
+#define Y_BED_SIZE 248
 
 // Travel limits (mm) after homing, corresponding to endstop positions.
 #define X_MIN_POS 0
 #define Y_MIN_POS 0
+
+// Travel limits after homing
 #define Z_MIN_POS 0
 #define X_MAX_POS X_BED_SIZE
 #define Y_MAX_POS Y_BED_SIZE
-#define Z_MAX_POS 200
+#define Z_MAX_POS 254
 
 /**
  * Software Endstops
@@ -1467,7 +1479,7 @@
  *   M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
  *   M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
  */
-//#define EEPROM_SETTINGS     // Persistent storage with M500 and M501
+#define EEPROM_SETTINGS     // Persistent storage with M500 and M501
 //#define DISABLE_M503        // Saves ~2700 bytes of PROGMEM. Disable for release!
 #define EEPROM_CHITCHAT       // Give feedback on EEPROM commands. Disable to save PROGMEM.
 #define EEPROM_BOOT_SILENT    // Keep M503 quiet and only give errors during first load
@@ -1688,7 +1700,7 @@
  * you must uncomment the following option or it won't work.
  *
  */
-//#define SDSUPPORT
+#define SDSUPPORT
 
 /**
  * SD CARD: SPI SPEED
@@ -1745,7 +1757,7 @@
 //
 //  Set this option if CLOCKWISE causes values to DECREASE
 //
-//#define REVERSE_ENCODER_DIRECTION
+#define REVERSE_ENCODER_DIRECTION
 
 //
 // This option reverses the encoder direction for navigating LCD menus.
@@ -1768,7 +1780,7 @@
 //
 // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
 //
-//#define INDIVIDUAL_AXIS_HOMING_MENU
+#define INDIVIDUAL_AXIS_HOMING_MENU
 
 //
 // SPEAKER/BUZZER
@@ -1776,7 +1788,7 @@
 // If you have a speaker that can produce tones, enable it here.
 // By default Marlin assumes you have a buzzer with a fixed frequency.
 //
-//#define SPEAKER
+#define SPEAKER
 
 //
 // The duration and frequency for the UI feedback sound.
@@ -1799,7 +1811,7 @@
 //
 // Note: Usually sold with a white PCB.
 //
-//#define REPRAP_DISCOUNT_SMART_CONTROLLER
+#define REPRAP_DISCOUNT_SMART_CONTROLLER
 
 //
 // Original RADDS LCD Display+Encoder+SDCardReader

Marlin/Configuration_adv.h

@@ -162,8 +162,8 @@
  * THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
  */
 #if ENABLED(THERMAL_PROTECTION_HOTENDS)
-  #define THERMAL_PROTECTION_PERIOD 40        // Seconds
-  #define THERMAL_PROTECTION_HYSTERESIS 4     // Degrees Celsius
+  #define THERMAL_PROTECTION_PERIOD 60        // Seconds
+  #define THERMAL_PROTECTION_HYSTERESIS 10    // Degrees Celsius
 
   //#define ADAPTIVE_FAN_SLOWING              // Slow part cooling fan if temperature drops
   #if BOTH(ADAPTIVE_FAN_SLOWING, PIDTEMP)
@@ -450,7 +450,7 @@
  * Multiple extruders can be assigned to the same pin in which case
  * the fan will turn on when any selected extruder is above the threshold.
  */
-#define E0_AUTO_FAN_PIN -1
+#define E0_AUTO_FAN_PIN 7
 #define E1_AUTO_FAN_PIN -1
 #define E2_AUTO_FAN_PIN -1
 #define E3_AUTO_FAN_PIN -1
@@ -463,7 +463,7 @@
 #define EXTRUDER_AUTO_FAN_TEMPERATURE 50
 #define EXTRUDER_AUTO_FAN_SPEED 255   // 255 == full speed
 #define CHAMBER_AUTO_FAN_TEMPERATURE 30
-#define CHAMBER_AUTO_FAN_SPEED 255
+#define CHAMBER_AUTO_FAN_SPEED 192
 
 /**
  * Part-Cooling Fan Multiplexer
@@ -549,7 +549,7 @@
 //
 // For Z set the number of stepper drivers
 //
-#define NUM_Z_STEPPER_DRIVERS 1   // (1-4) Z options change based on how many
+#define NUM_Z_STEPPER_DRIVERS 2   // (1-4) Z options change based on how many
 
 #if NUM_Z_STEPPER_DRIVERS > 1
   //#define Z_MULTI_ENDSTOPS
@@ -1599,10 +1599,10 @@
  *
  * See https://marlinfw.org/docs/features/lin_advance.html for full instructions.
  */
-//#define LIN_ADVANCE
+#define LIN_ADVANCE
 #if ENABLED(LIN_ADVANCE)
   //#define EXTRA_LIN_ADVANCE_K // Enable for second linear advance constants
-  #define LIN_ADVANCE_K 0.22    // Unit: mm compression per 1mm/s extruder speed
+  #define LIN_ADVANCE_K 0.08    // Unit: mm compression per 1mm/s extruder speed
   //#define LA_DEBUG            // If enabled, this will generate debug information output over USB.
   //#define EXPERIMENTAL_SCURVE // Enable this option to permit S-Curve Acceleration
 #endif
@@ -2092,7 +2092,7 @@
 #if HAS_DRIVER(TMC26X)
 
   #if AXIS_DRIVER_TYPE_X(TMC26X)
-    #define X_MAX_CURRENT     1000  // (mA)
+    #define X_MAX_CURRENT     1330  // (mA)
     #define X_SENSE_RESISTOR    91  // (mOhms)
     #define X_MICROSTEPS        16  // Number of microsteps
   #endif
@@ -2104,7 +2104,7 @@
   #endif
 
   #if AXIS_DRIVER_TYPE_Y(TMC26X)
-    #define Y_MAX_CURRENT     1000
+    #define Y_MAX_CURRENT     1680
     #define Y_SENSE_RESISTOR    91
     #define Y_MICROSTEPS        16
   #endif
@@ -2140,7 +2140,7 @@
   #endif
 
   #if AXIS_DRIVER_TYPE_E0(TMC26X)
-    #define E0_MAX_CURRENT    1000
+    #define E0_MAX_CURRENT    1330
     #define E0_SENSE_RESISTOR   91
     #define E0_MICROSTEPS       16
   #endif
@@ -2213,7 +2213,7 @@
   #define INTERPOLATE       true  // Interpolate X/Y/Z_MICROSTEPS to 256
 
   #if AXIS_IS_TMC(X)
-    #define X_CURRENT       800        // (mA) RMS current. Multiply by 1.414 for peak current.
+    #define X_CURRENT       846        // (mA) RMS current. Multiply by 1.414 for peak current.
     #define X_CURRENT_HOME  X_CURRENT  // (mA) RMS current for sensorless homing
     #define X_MICROSTEPS     16    // 0..256
     #define X_RSENSE          0.11
@@ -2229,7 +2229,7 @@
   #endif
 
   #if AXIS_IS_TMC(Y)
-    #define Y_CURRENT       800
+    #define Y_CURRENT      1069
     #define Y_CURRENT_HOME  Y_CURRENT
     #define Y_MICROSTEPS     16
     #define Y_RSENSE          0.11
@@ -2277,7 +2277,7 @@
   #endif
 
   #if AXIS_IS_TMC(E0)
-    #define E0_CURRENT      800
+    #define E0_CURRENT      846
     #define E0_MICROSTEPS    16
     #define E0_RSENSE         0.11
     #define E0_CHAIN_POS     -1
@@ -2531,7 +2531,7 @@
    * Enable M122 debugging command for TMC stepper drivers.
    * M122 S0/1 will enable continous reporting.
    */
-  //#define TMC_DEBUG
+  #define TMC_DEBUG
 
   /**
    * You can set your own advanced settings by filling in predefined functions.